win10 bcd修復命令,windows10bcd修復

win10 bcd修復命令

以下為Win10 bcd修復命令：

1. 打開一個管理員權限的命令提示符，方法為右鍵單擊‘開始’菜單，選擇‘命令提示符(管理員)’。

2. 輸入以下命令以備份原有的引導文件

bcdedit /export C:\BCD_Backup

3. 依次執行以下命令：

bootrec /fixboot

bootrec /scanos

bootrec /rebuildbcd

4. 如果上述命令無法修復引導文件，可以執行以下命令：

bootrec /repairbcd

bootrec /fixmbr

bootrec /fixboot

5. 最后輸入以下命令重新開始計算機：

shutdown /r /t 0

以上是Win10 bcd修復命令，希望對您有所幫助。注意：在執行這些命令之前，請備份數據以及引導分區，以防數據損失。

windows10bcd修復

There are a few ways to repair or rebuild the boot configuration data (BCD) on a Windows 10 computer, depending on the specific issue and level of access to the system. Here are some possible steps you can try:

1. Use automatic repair

If your Windows 10 computer cannot start up properly due to BCD errors, you can use the automatic repair feature built into the operating system. This feature can help diagnose and fix startup issues, including problems with BCD. Here's how to perform an automatic repair:

1. Insert the Windows 10 installation media (such as a DVD or USB flash drive).

2. Restart your computer and boot from the installation media.

3. Select your language preferences and click Next.

4. Click on the "Repair your computer" option in the lower left corner.

5. Choose "Troubleshoot" and then "Advanced options."

6. Select "Startup Repair" and follow the on-screen instructions to complete the repair process.

Note that the exact steps may vary depending on your system and installation media.

2. Use bootrec commands

If the automatic repair option doesn't work or you have more advanced issues with BCD, you can use the command prompt and run some bootrec commands to repair or rebuild the BCD. Here are the steps:

1. Boot your computer from the Windows 10 installation media as described above.

2. Choose "Command Prompt" from the advanced options screen.

3. Type the following commands one at a time and press Enter after each one:

bootrec /fixmbr

bootrec /fixboot

bootrec /scanos

bootrec /rebuildbcd

4. Follow the prompts and answer "Y" or "Yes" if prompted to add the Windows installation to the BCD.

5. Restart your computer and check if the BCD issues have been resolved.

3. Use recovery options

If your Windows 10 system has a recovery partition (or you have created a system image or backup), you can use the recovery options to restore your computer to a previous state before the BCD errors occurred. Here's how to do it:

1. Restart your computer and repeatedly tap the F11 key (or another key depending on your system) during boot to access the recovery options.

2. Choose "Troubleshoot" and then "Advanced options."

3. Select "System Restore" or "System Image Recovery" and follow the on-screen instructions to restore your system to a previous state when it was working properly.

4. Check if the BCD issues have been resolved after the restore process is complete.

Note that system restore or system image recovery may erase some of your recent data, so make sure to back up your important files before attempting this option.

In any case, if you're not comfortable or confident with these steps, you may want to seek professional help or contact Microsoft support for further assistance.

win10 bcd修復工具

1. 在Windows 10的安裝媒體（如USB安裝盤或恢復磁盤）中進入“修復你的電腦”。

2. 選擇“疑難解答”>“高級選項”>“命令提示符”。

3. 在命令提示符中輸入“bootrec /fixmbr”、“bootrec /fixboot”，以及“bootrec /rebuildbcd”。

4. 重啟計算機，檢查問題是否已解決。

請注意，在使用命令提示符時，請按照提示輸入正確的命令以避免出現問題。此外，始終備份您的數據以防萬一。

win10boot bcd錯誤修復

以下是修復Win10引導BCD錯誤的步驟：

1.使用Windows 10安裝媒介，進入“安裝界面”。

2.在安裝界面的頂部，選擇“修復您的電腦”。

3.在接下來的界面中，選擇“疑難解答”選項。

4.在疑難解答界面中，選擇“高級選項”。

5.在高級選項界面中，選擇“命令提示符”。

6.在命令提示符中，輸入“bootrec /fixmbr”并按回車鍵。

7.完成后，再輸入“bootrec /fixboot”并按下回車鍵。

8.最后，再輸入“bootrec /rebuildbcd”并按下回車鍵。

9.在命令執行完畢后，退出命令提示符窗口，關閉計算機。

10.重新啟動計算機，看看是否修復了BCD錯誤。

bcd修復win7

為了修復Windows 7的BCD，請按照以下步驟操作：

1. 插入Windows 7安裝盤或恢復盤，啟動計算機。

2. 在語言選項頁面上，選擇您的語言和其他首選項，然后單擊下一步。

3. 在下一頁面上，單擊"修復您的計算機"。

4. 選擇"使用命令提示符"。

5. 在命令提示符中，鍵入以下命令并按Enter鍵：bootrec /fixmbr

6. 然后鍵入以下命令并按Enter鍵：bootrec /fixboot

7. 最后，鍵入以下命令并按Enter鍵：bootrec /rebuildbcd

8. 如果命令提示您添加一個新的操作系統，請鍵入Y并按Enter鍵，然后繼續操作。

9. 重啟計算機并移除安裝盤。

這些步驟應該能夠成功修復Windows 7的BCD。如果仍然遇到問題，請考慮查看更詳細的指南或聯系計算機專家以獲取更好的支持。